CRAIN #835 UNDERCUT SAW
This saw undercuts doors in place, inside corner areas, and can undercut masonry walls and hearths. A diamond blade (No. 822) is available as an accessory for undercutting tile and stone. Features slip-proof height adjustment from flush to the floor to as high as one inch using dual lead screws for setting and holding the height. The aluminum ratchet front handle is very durable and folds down for undercutting toe spaces. The powerful 13 AMP motor is geared to produce more torque at a lower RPM, and also throws less dust. Dust port can be attached to a vacuum (not included) for dust collection. Doors that are as thick as 1 5/8” can be undercut without removal. Comes with carbide blade, masonry composition blade, carrying case, blade wrench, and instructions. Replacement blades: No. 836 Carbide (wood only), No. 805 Masonry, No. 822 Diamond (not included). Net weight: 21.5 lbs.
CRAIN #575 SAW
The 575 Undercut Saw undercuts along walls, door undercuts, under toe spaces, and will also fully undercut inside corners.
The height of cut is easily adjustable from flush to one inch above the floor. The large, flat base prevents tipping and assures accurate, level cutting.
The dual-angle depth gauge is a Crain exclusive and allows undercutting at a “straight-on” or a 45 degree angle.
A visual adjustment scale provides precision depth control at 1/8″ increments.
Specifications:
- Rating: 120 Volt AC
- Amperage: 7.0
- No-load RPM: 11,000
- Max Cutting Height: 1″
- Max Cutting Depth: 1-1/4″
- Weight: 11.0 lbs
Features:
- Heavy duty industrial motor.
- Easy height adjustment.
- “Dual angle” precision depth gauge.
- Cuts inside corner completely.
- Cuts flush to the floor with a carbide blade
ROBERTS #10-55 LONG NECK UNDERCUT SAW
SPECIFICATIONS
Item No: 10-55
Voltage: 120V-60Hz
AMPS: 9.5 (industrial grade)
WATTS: 1050
RPM: 8,000
Powered by an 8000 RPM, 1050 watt motor, the 10-55 LONGNECK 6″ undercut Saw easily cuts door undercuts, baseboard, cabinet toe kicks, inside corners and most hanging doors.
The cutting height is easily adjustable from flush to 1-1/16” when working with different floor covering thicknesses and the oversized flat base provides accurate, level cutting.
The extended tail of the Roberts LONGNECK offers better control of the undercut Saw and more leverage against torque.
The trigger is located on the tail, enabling the trigger to easily be held in the ON position. The trigger is non-locking to comply with OSHA requirements.
ROBERTS #10-46 SUPER 6″ UNDERCUT SAW
Adjustable cutting depth guide prevents cutting into plaster or wall board when trimming base boards.
Includes custom molded carrying case and 6-3/16″ carbide tipped blade.
Description:
- Adjustable cutting depth guide prevents cutting into plaster or wall board when trimming base boards
- Powerful, 5.8 amp, 900 Watt industrial grade power unit has all ball and needle bearings
- Patented design enables saw to cut full inside corners in molding up to 1/2″ thick
- Spiral ground gears for smooth, quiet operation
- Precision height adjustment from “flush” to 1-1/16″
- Cuts up to 1-3/4″ deep
- Includes custom molded carrying case and 6-3/16″ carbide tipped blade
- Uses 10-47 Carbide Tip Replacement Blades
BLADE #821
6-1/2″ Crain 821 Carbide Tipped Repl Blade
- 40 tooth, carbide-tipped.
- Best for undercutting along walls and door undercuts.
- Use with Crain 812 Super Cut Saw, Crain 820 Heavy Duty Undercut Saw, or Crain 825 Heavy Duty Undercut Saw.
BLADE 10-47 ROBERTS
4 1/2 inch tape with reinforcing scrim. Recommended for most seaming.
Ideal for repairs, borders,custom rugs and decorative work because the tape can be over- lapped.
This tape works on all common backings.
BLADE #556 CRAIN
The 36-tooth carbide blade is bell-shaped for added rigidity.
Only for Crain 555 Multi-Undercut Saw.
BLADE #836 CRAIN
